Very Narrow Aisle Training Courses (Operator Up)

Home > Forklift Training Courses > Very Narrow Aisle Training Courses

The Very Narrow Aisle Lift Truck

A very narrow aisle lift truck or forklift truck often shortened to just VNA is a modern take on the traditional forklift truck. These machines excel in narrow aisles, needing only a few centimetres clearance either side of the truck. They are guided in these narrow spaces by either wire or rails and many of them have added extras including warehouse navigation, positioning aids, and cameras. Picking orders can be sent to the machine via radio data. Their rated capacity is around 1 - 1.6 tonnes with some models able to lift in excess of 15 metres high.

Their large batteries enable them to be run for many hours often for a double shift, charging is from a separate charger cabinet.

 

Very Narrow Aisle Training Courses

This forklift training course contains theory work in a classroom and practical using a very narrow aisle (VNA) truck. The classroom work consists of learning about Health and Safety legislation. Also, the theory of using a VNA truck and the operator’s safety code. The practical work builds so that trainees gain knowledge and experience gradually. Adequate time to practice is important, before moving onto the next stage. This training culminates with 3 stages of testing:

  • A theory test – consisting of 25 questions
  • Pre-use inspection test
  • Practical skills test involving various manoeuvres completed in a safe manner.
Very narrow aisle fift truck
Very narrow aisle forklift truck

Machine:

Very Narrow Aisle (Operator Up)

Category:

F1

Specification:

Operator Up

Accrediting Body:

Independent Training Standards Scheme & Register (ITSSAR)

Ratio:

3 : 1 : 1 (3 operators, 1 instructor, 1 machine)

Duration:

Novice - 1 operator = 3 days, 2 operators = 4 days, 3 operators = 5 days

Experienced - 1 operator = 2 days, 2 operators = 2 days, 3 operators = 3 days

Safety Refresher - 1 operator = 1 day, 2 operators = 1 day, 3 operators = 1 day

Conversion - contact us

Cost:

Contact us

 

The following list are the elements that make up a novice very narrow aisle truck training course. For experienced operators, safety refresher and conversion courses the list would be shorter.

  • Course induction
  • The need and reasons to training and statutory requirements (HASAWA 1974 etc.)
  • Introduction to equipment/control familiarisation/ principles of operation
  • Identification/use/adjustment of attachments in pre-determined positions including forks
  • Recommended mount and dismount
  • Introduction to motive, steering controls and practice
  • Basic steering exercises – simple courses
  • Advanced steering exercises – figure of 8/chicane/90° approaches
  • Battery charging procedures/maintenance
  • Operator safety code and relevant handout
  • Daily pre-use inspections
  • Engineering principles/rated capacity/stability
  • Simple hydraulics (theory)
  • Introduction to hydraulic controls, handling empty pallets low level
  • Load types/handling and weight assessment
  • Stacking/de-stacking at low; eye and high level on industrial racking*
  • Stacking/destacking at low; eye and high level bulk stacks*
  • Stacking/destacking at low; eye and high level cup post pallets*
  • Manoeuvring with loads/ramps and inclines/handling awkward loads*
  • Relevant safety film
  • Vehicle loading and unloading (theory)*
  • Vehicle loading and unloading (practical)*
  • Multi choice theory test
  • Pre-use inspection test
  • Practical skills test

* To be covered where relevant to operation or facilities permit

Levels of Training

Novice Operator Training

This course is for operators who have little or no experience. The objective is to equip students with the confidence, knowledge and skills to safely and efficiently operate a very narrow aisle truck.

Experienced Operator Training

For operators who are competent and experienced on a very narrow aisle truck. But, either have not received any kind of approved training, do not hold a certificate, or their certificate is over 5 years old.

Safety Refresher Training*

This is for operators who have a certificate that is under 5 years old. Also, appropriate where operators; have not used trucks for some time, are occasional users, have developed unsafe working practices, had an accident or near miss, or changed their working practices/environment.

Conversion Training*

For training on a similar truck to one that an operator has already been successfully trained, tested and certified on. Any relevant certificate must be under 5 years old.

* Certification must be provided before commencement of any training

Facilities Required

You will need sufficient space for candidates and an instructor to carry out theory lessons. For practical work you’ll need a very narrow aisle truck. Also, you will need ample space to carry out training, assessments and testing.

All operators will need safety shoes/boots plus any other PPE as per the company’s internal risk assessments.

 

On-site Training

All training courses are carried out on our customer’s premises. This gives our students the advantage of being trained and tested on a machine that is known to them. And after successful completion of training, operators will know how to use these machines safely and efficiently.

Certificates

On completion of our training courses operator's will receive:

  • Course hand out
  • A4 ITSSAR accredited certificate
  • Plastic photo identification card

An operator will then have their details entered or edited on ITSSAR’s TOPS (Trained Operator Passport Scheme) database.

VNA licence or ITSSAR certificate, plastic I.D. card and course handout
VNA certificate and course hand out

Not found what you are looking for? How about these?

How many forklift categories are there?

There are currently over 50 different industrial lift truck groups. To use any of the lift trucks in these groups an operator must be trained, tested and authorised (by their employer).